Product ID:YELLOW OXIDE MACHINE COLORANT C, 96-3 (0708
MSDS Date:08/14/1989
FSC:8010
NIIN:00N025493
MSDS Number: BMQYX

PPG INDUSTRIES INC (WAS PTTTSBURGH PLATE GLASS CO)

260 KAPPA DR
PITTSBURGH, PA 15238
US

Emergency Phone: 304-843-1300

Info Phone: 412-963-5822

Cage: 47695

PPG INDUSTRIES INC

PITTSBURGH, PA 15272 US

Telephone: 1-800-245-2974 (CAL HYPO)

Cage: 47695

IRON OXIDE

CAS: 51274-00-1

Fraction By Weight: 55-60%

OSHA PEL 10 MG/M3 (FE)

ACGIH TLV: 5 MG/M3 (FUME) (FE)

ETHYLENE GLYCOL

CAS: 107-21-1

RTECS: KW2975000

Fraction By Weight: 10-15%

OSHA PEL 50 PPM, C

ACGIH TLV: 50 PPM VAPOR, C

EPA Report Quantity: 1 LB

DOT Report Quantity: 1 LB

WATER; (DEIONIZED WATER)

CAS: 7732-18-5

RTECS: ZC0110000

Fraction By Weight: 1-2%

WATER

CAS: 7732-18-5

RTECS: ZC0110000

Fraction By Weight: 1-2%

FILM FORMERS, RESINS, AND ADDITIVES

Fraction By Weight: 5-10%

EXPOS LIMITS, THE LEL BELOW THE STATED LIMIT, AND TO

RTECS: 9999999ZZ

ON SURFS COATED WITH THIS PRODUCT.

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INGEST:HARMFUL/FATAL, EYE:CAUSES SEV
IRRIT. SKIN:MAY CAUSE MODERATE IRRIT. MAY BE ABSORBED THRU SKIN.
INHAL:VAP & SPRAY MIST MAY BE HARMFUL. VAP GENERATED AT ELEVATED
TEMPS IRRITATES EYES, NOSE & THRO AT. CHRONIC: AVOID LONG TERM AND
REPEATED CONTACT. INGEST OF PRODS CONTAINING ETHYLENE GLYCOL MAY
DAM KIDNEY & LIVER.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:REDNESS, ITCHING, BURNING SENSATION AND VISUAL
DISTURBANCES MAY INDICATE EXCESSIVE EYE CONTACT. DRYNESS, ITCHING,
CRACKING, BURNING, REDNESS, AND SWELLING ARE CONDITIONS ASSOCIATED
WITH EXCESSIVE SKIN CONTACT.

First Aid:INGEST:DO NOT INDUCE VOMIT. EYE:FLUSH IMMED W/PLENTY OF WATER
FOR AT LEAST 15 MIN. SKIN:FLUSH IMMED W/PLENTY OF WATER FOLLOWED BY
WASHING W/SOAP & WATER. INHAL:IF AFTD BY INHAL OF VAP/SPRAY MIST,
REMO VE TO FRESH AIR. APPLY ARTF RESP & OTHER SUPPORTIVE MEASURES
AS REQD. OTHER:IF ANY OF THE FOLLOWING OCCUR DURING/FOLLOWING USE
OF PROD, CONT A POIS CTL CTR, EMER ROOM/MD IMMED; HAVE MATL (SUPP
DATA)

Flash Point Method:PMCC
Extinguishing Media:USE NFPA CLASS B EXTING (CO*2/DRY CHEM/UNIVERSAL AQ
FILM FORMING FOAM) DESIGNED TO EXTING NFPA CLASS IIIB LIQ FIRES.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPRVD SCBA & FULL PROT EQUIP
. WATER SPRAY MAY BE INEFTIVE. WATER SPRAY MAY BE USED TO COOL CLSD
CNTNRS TO PVNT PRESSURE (SUPP DATA)
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE OR BURST
(DUE TO THE BUILD-UP OF STEAM PRESSURE) WHEN EXPOSED TO EXTREME
HEAT.

Spill Release Procedures:PROVIDE MAXIMUM VENT. ONLY PERSONNEL EQUIPPED
W/PROPER RESP & SKIN & EYE PROT SHOULD BE PERMITTED IN THE AREA.
REMOVE ALL SOURCES OF IGNITION. TAKE UP SPILLED MATERIAL W/SAWDUST,
VERMICULITE, OR OTHER ABSORBENT MATL & PLACE INTO CONTAINERSFOR
DISP.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:DO NOT STORE ABOVE 120F. STORE LARGE
QUANTITIES IN BUILDING DESIGNED AND PROTECTED FOR STORAGE OF NFPA
CLASS IIIB LIQS. PROTECT FROM FREEZING.
Other Precautions:IF THIS MATERIAL IS PART OF A MULTIPLE COMPONENT
COATING SYSTEM, READ THE MATERIAL SAFETY DATA SHEETS FOR THE OTHER
COMPONENT OR COMPONENTS BEFORE BLENDING AS THE RESULTING MIXTURE
MAY HAVE THE HAZARD S OF ALL OF ITS PARTS.

Respiratory Protection:WHERE VENTILATION IS INADEQUATE, USE A SUITABLE
NIOSH/MSHA APPROVED RESPIRATOR .
Ventilation:PROVIDE GEN DILUTION/LOCAL EXHST VENT IN VOL & PATTERN TO
KEEP CONC OF INGS LISTED BELOW THE LOWEST SUGGESTED (ING 6)
Protective Gloves:NITRILE, NEOPRENE, OR LATEX GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:WEAR PROTECTIVE CLOTHING, INCLUDING
IMPERMEABLE APRON.
Work Hygienic Practices:CLEAN OR DISCARD CONTAMINATED CLOTHING AND
SHOES.
Supplemental Safety and Health
FIRE FIGHT PROC:BUILD-UP & POSS AUTOIGNIT/EXPLOS WHEN EXPOS TO HEAT. IF
WATER IS USED, FOG NOZZ ARE PREF. HAZ DECOMP PROD:FUMES
INCLUDING:CARBON MONOXIDE. FIRST AID PROC:SAFETY DATA SHEET
INFORMATION AVAILABLE. INGEST/EXCESSIVE EXPOS TO A CORR MATL.
PERSISTENT SKIN/EYE IRRIT/BRTHG DFCLTS.

HCC:N1
Boiling Pt:B.P. Text:>180F,82C
Vapor Pres:15.2
Vapor Density:HVR/AIR
Spec Gravity:1.78
Evaporation Rate & Reference:24 (BUOAC=100)
Solubility in Water:38.6%
Appearance and Odor:VISCOUS LIQUID WITH AN ODOR CHARACTERISTIC OF THE
CHEM FAMILY & ANY SOLVENTS.
Percent Volatiles by Volume:57.4

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG ALKALIES, STRONG MINERAL ACIDS, OR STRONG
OXIDIZING AGENTS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:MAY PRODUCE HAZ DECOMP PRODS WHEN
HEATED. WELDING/BRAZING/FLAME-CUTTING ON SURFS COATED W/PROD MAY
PRODUCE (SUPP DATA)

Waste Disposal Methods:WASTE MATERIAL MUST BE DISPOSED OF I/A/W
FEDERAL, STATE, PROVINCIAL, AND LOCAL ENVIRONMENTAL CONTROL
REGULATIONS. EMPTY CONTAINERS SHOULD BE RECYCLED OR DISPOSED OF
THROUGH AN APPROVED WASTE MANAGEMEN T FACILITY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.